Звуков процесор Helix DSP.2

Звуков процесор Helix DSP.2

на 12 вноски по 63.88 лв.

- Extremely powerful “fixed point” Audio DSP with 64 Bit resolution and 1.2 billion MAC operations per second
- HELIX Extension Card slot (HEC) for additional input / output modules like Bluetooth® Audio Streaming, High-Resolution Audio Streaming via USB etc.
-Smart highlevel input with ADEP circuit (Advanced Diagnostics Error Protection)
-Start-Stop capability down to 6V supply voltage
-Freely definable signal routing with separate matrices for line, SPDIF and HEC/AUX
-Time alignment with up to 20 ms delay time per channel, additionally reverse time alignment for in-phase summation of the inputs
-Optimized signal path and power supply for further improved sound quality
-“Ground lift” switch to avoid ground loops
-Control input for connecting remote controls and accessories
-Inputs: 6 x RCA/Cinch, 6 x Highlevel and 1 x optical SPDIF
-Outputs: 8 x RCA/Cinch with max. 6 Volts output voltage
-Easy configuration thanks to the professional and user-friendly DSP PC-Tool Version 4 software

Special features:
Smart highlevel input
The latest generation of OE car radios incorporates sophisticated possibilities of diagnosing the connected speakers. If a common signal processor will be hooked up failure messages and loss of specific features (e.g. fader function) quite often appears - but not with the DSP.2.
The new ADEP circuit (Advanced Diagnostics Error Protection) avoids all these problems without loading the speaker outputs of the OE radio during high volumes unnecessarily.

Power Save Mode
The Power Save Mode is incorporated in the basic setup. It allows to significantly reduce the power consumption of the amplifiers that are connected to the HELIX DSP.2 once there’s no input signal present for more than 60 seconds. Please note that in many up-to-date cars with “CAN” or any other internal bus structures it may happen that the radio remains “invisibly” turned on for up to 45 min. even after locking and leaving the car! Once the “Power Save Mode“ is active the remote output and therefore the connected amplifiers will be turned off. The HELIX DSP.2 will reactivate the remote output within a second if a music signal is applied. It is possible to either modify the turn-off time of 60 sec. or completely deactivate the “Power Save Mode” via the
DSP PC-Tool software.

Start-Stop capability
The switched power supply of the HELIX DSP.2 assures a constant internal supply voltage even if the battery’s voltage drops to 6 Volts during engine crank.

Automatic Digital Signal Detection
Switching from analog input to the digital input is done automatically as soon as a signal is detected on the Optical Input. This feature can be deactivated in the DSP PC-Tool software. Alternatively you can use an optional remote control for manual switching between analog and digital inputs.


Inputs     6 x RCA / Cinch, 6 x Highlevel speaker input, 1 x Optical SPDIF (12 - 96 kHz), 1 x Remote In
Input sensitivity     RCA / Cinch 2 - 4 Volts
Highlevel 3.5 - 11 Volts
Outputs     8 x RCA / Cinch, 1 x Remote Out
Output voltage     6 Volts
Frequency response     10 Hz - 22,000 Hz
DSP resolution     64 Bit
DSP power     295 MHz (1.2 billion MAC operations/second)
Sampling rate     48 kHz
DSP type     Audio signal processor
Signal converters     A/D: BurrBrown, D/A: BurrBrown
Signal-to-noise ratio digital input     112 dB (A-weighted)
Signal-to-noise ratio analog input     107 dB (A-weighted)
Total harmonic distortion (THD+N) digital input     < 0.0008 %
Total harmonic distortion (THD+N) analog input     < 0.002 %
IM distortion (IMD) digital input     < 0.003 %
IM distortion (IMD) analog input     < 0.005 %
Crosstalk     > 90 dB
Operating voltage     9.6 - 18 Volts (max. 5 sec. down to 6 Volts)
Current draw     < 480 mA
Max. remote output current     500 mA
Additional features     HEC slot, Ground lift switch, Control Input, ADEP circuit, Auto Remote switch
Dimensions (H x W x D)     40 x 177 x 120 mm

0 лв
Аval-bg.com ® Всички права запазени